SIMULATION ANALYSIS OF ERGONOMIC DESIGN OF ELECTRIC MOTORBIKE FRAMES FOR RESIDENTIAL COMMUNITIES

Dwiky Ibrahim Kiki(1*), Rizal Hanifi(2)


(1) Universitas singaperbangsa karawang
(2) Universitas singaperbangsa karawang
(*) Corresponding Author

Abstract


Electric motorbikes are an economical and environmentally friendly means of transportation but have limitations on cruising and speed. In its development began to be used motorcycles with gasoline fuel. On the one hand, it is able to overcome the limitations of cruising power and speed, but on the other hand, it causes air pollution. To overcome this comes the technology of electric motorbikes. This electric bike does not cause air pollution because there is no combustion that occurs, has only an alight drawback which is limited electrical power and the length of time for recharger. In motor vehicles, the frame is the most important part that will hold and as a seat of various components, and support a load of these components on the vehicle system. Calculation of skeletal strength is very important to ensure the frame is able to withstand the load. Calculation of frame strength can be done manually (hand calculation) or by using Finite Element Analysis (FEA). on this frame, strength calculation using finite element analysis (FEA) with Solidworks software 2018. By using simulation can be known the value of von mises, displacement, and safety factors. from the results of the analysis of the smallest safety factor rider weight, 170 kg = 2.58. The results of the analysis of the construction of electric motorcycle frames carried out on static loading are safe because it is less than the minimum value of the safety factor of 1.25


Keywords


Electric Motorbike, Simulation, Ergonomic, Frame, Ergonomi

Full Text:

PDF

References


Ahmad Mukhlis, O. J. (2017). KAJIAN TEKNOLOGI PADA SEPEDA MOTOR BERTENAGA LISTRIK. Jurnal Inosains Volume 12 Nomor 2, 41.

Amalia, M. (2018). PERANCANGAN SEPEDA MOTOR LISTRIK MENGGUNAKAN METODE KANSEI ENGINEERING .

Arman. (2020). PERANCANGAN SEPEDA LISTRIK MENGGUNAKAN MOTOR BLDC DENGAN PENGGERAK DEPAN UNTUK AREA PERUMAHAN. Prosiding 4th Seminar Nasional Penelitian & Pengabdian Kepada Masyarakat, 90-96.

Awaluddin, M. (2019). Analisa Kekuatan Rangka Sepeda Listrik Menggunakan Software SolidWorks . Journal of Technical Engineering: Piston Vol. 3, No. 1, 5-16.

Fauzi, A. (2020). ANALISA KONSUMSI DAYA MOTOR LISTRIK PADA SEPEDA MOTOR HYBRID DENGAN VARIASI LAJU KECEPATAN BERBASIS MICROCONTROLLER.

Imran, A. I. (2018). PERANCANGAN, ANALISA DAN SIMULASI RANGKA SEPEDA LISTRIK UNTUK MASYARAKAT PERKOTAAN. DINAMIKA Jurnal Ilmiah Teknik Mesin Vol. 9, No. 2, 53-58.

Kuswardana, a. (2016). TUGAS AKHIR ANALISIS SISTEM MOTOR PENGGERAK PADA MOBIL LISTRIK DENGAN KAPASITAS SATU PENUMPANG.

Pattiapon, D. R. (2019). PENGGUNAAN MOTOR SINKRON TIGA PHASA TIPE SALIENT POLE SEBAGAI . JURNAL SIMETRIK VOL.9, NO.2, DESEMBER 2019, 207.

Putra, H. (2019). Perancangan Sepeda Listrik Dengan Menggunakan Motor DC Seri. Jurnal Fokus Elektroda : Energi Listrik, Telekomunikasi, Komputer, Elektronika dan Kendali) Volume 04 No 02, Tahun 2019, http://ojs.uho.ac.id/index.php/jfe/

Satria, D. (2017). ANALISA PERHITUNGAN ENERGI LISTRIK PADA SEPEDA. Jurnal Mesin Teknologi (SINTEK Jurnal) Volume 11 No. 1, 19.

Siahaan, R. (Juni 2012). ANALSIS ERGONOMI TERHADAP SEPEDA ANAK-ANAK BERDASARKAN DATA ANTROPOMETRI MENGGUNAKAN METODE POSTUREEVALUATION INDEX (PEI) VIRTUAL ENVIRONMENT.

Suwandi, A. (2017). PERANCANGAN SEPEDA STATIS PENGHASIL ENERGI LISTRIK YANG . Jurnal Teknik Mesin Untirta Vol. III, No. 2, , hal. 24 31,

Ahmad Mukhlis, O. J. (2017). KAJIAN TEKNOLOGI PADA SEPEDA MOTOR BERTENAGA LISTRIK. Jurnal Inosains Volume 12 Nomor 2, , 41-49

Satria, D. (2017). ANALISA PERHITUNGAN ENERGI LISTRIK PADA SEPEDA. Jurnal Mesin Tekno Soebroto, S.W., 2000, Prinsip-Prinsip Perancangan Berbasiskan Dimensi Tubuh

Soebroto, S.W., 2000 (Antropometri) Dan Perancangan Stasiun Kerja, Lokakarya IV Methods Engineering: Adaptasi ISO/TC159 (Ergonomics) dalam Standar nasional Indonesia (SNI), Laboratorium Perancangan Sistem Kerja & Ergonomi ITB, Bandung. gi (SINTEK Jurnal) Volume 11 No.1, 19-26.

Faj'ri, M. H. (2018). Desain sepeda listrik dengan style motor boardtrack sebagai sarana mobilitas perkotaan yang cepat dan efisien .

FAUZI, A. (2020). ANALISA KONSUMSI DAYA MOTOR LISTRIK PADA SEPEDA MOTOR HYBRID DENGAN VARIASI LAJU KECEPATAN BERBASIS MICROCONTROLLER.

Maercielo, D. (2015). PERANCANGAN DAN ANALISIS KEKUATAN KONTRUKSI DAN POWERTRAIN PAA PROTOTYPE HAND-CRANK CYCLE (SEPEDA ENGKOL TANGAN). JURNAL KAJIAN TEKNOLOGI VOL. 11 NO. 1, 69-79.

Setyon, B. (2016). PERRANCANGAN DAN ANALISIS KEKUATAN FRAME SEPEDA HYBRID tRISONA MENGGUNAKAN SOFTWARE AUTEDESK INVENTOR . Jurnal IPTEK VOL.20 No. 2, 37-46.


Article Metrics

Abstract view : 270 times
PDF - 48 times

DOI: https://doi.org/10.26714/traksi.22.2.2022.162-174

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 TRAKSI

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.


TRAKSI : Majalah Ilmiah Teknik Mesin

ISSN : 1693-3451 (Pinted) e-ISSN : 2579-9738 (Online)

Published by: LP2M Unimus bekerjasama dengan APTI (Asosiasi Profesi Teknik Indonesia)  

 
ADDRESS

Jl. Kasipah No. 12 Semarang

E-mail: traksi@unimus.ac.id Call: 0248445768


Sponsors

Asosiasi Profesi Teknik Indonesia (APTI)

Website: www.apti.or.id